Examining Computer Hardware Components

1. Checking the Screen or Monitor
The screen of your computer or monitor has pixels. These pixels have three colors: Red, green and blue. Pixels can often be damaged or stop functioning properly displaying only one color or just being black.

There is an online tool to check for bad pixels called "CheckPixels" The test at CheckPixels will display your three main colors mentioned above and if a pixel is dead, it will show as a black spot and if a pixel is glowing a different color ( Malfunctioning) you will see that too.

2. Checking the Keyboard
The keyboard might not seem important as a hardware component, but it is used in almost all tasks and taken for granted. For laptop users, the keyboard is very important. If one has to send the laptop away for repair the entire computer must go with it. There is also an online test tool available to test all your keyboard keys called "KeyboardTester".

3. Checking the Disk Drive (HDD & SSD)
Your HDD / SSD has your operating system and most of your applications and files. Having your HDD / SDD completely healthy is very important. This is most imperative when dealing with a used computer since you have no awareness of the previous history or care of the used computer and its HDD / SDD.

Different tools are available to check the condition and health of the HDD / SDD.

HDSentinel is one you can use for your HDD. The left hand side of the screen will display drives connected the computer. Health is the main parameter to look for. HD Sentinel will explain the meaning of the health percentages and the steps that you should take based on the results. As an example, you should not throw out your HDD just because of a few bad disk sectors and IO errors.

SSDlife is another tool specifically for an SSD. It also shows health in percentages and the expected life of the drive. Similar to hard disks, bad sectors can occur in SSDs.

4. Checking the Processing Units (CPU & GPU)

The main components that do all the processing are the Central Processing Unit (CPU) and the Graphics Processing Unit (GPU). These are the components that allow you to run your office applications and your games. These are also essential components to ensure are in perfect working order. So it is necessary that these two components should be in perfect condition. For testing both, we use CPU speed test

For testing your GPU, the tool.Base Mark Web 3.0 works just fine.

5. Checking the Random Access Memory (RAM)

RAM is the one essential component that has the most immediate impact on your computers performance. MemTest from HCI Design is a great tool to check your unused memory for errors. Identifying and fixing errors with your RAM is important. Errors in RAM cause the infamous "blue screen of death". Boot problems can also be attributed to RAM errors.

Conclusion
Besides the hardware component tests above, you should also check your Ethernet ports and connection, wireless connection from the wireless card (internal or external), HDMI, DVI and USB connections using available cabling and devices.

Posted in general | Comments Off on Examining Computer Hardware Components

How to Change the MPI Node Address For a Siemens S7-300 PLC

I have seven Siemens S7-300 PLCs connected together using the MPI (Multi Point Interface) interface. The Siemens MPI protocol is used by Siemens PLCs to communicate with external devices. I want to rename each of the seven PLCs. Here are the steps to accomplish that task.

First, connect your MPI cable to the first PLC. I will be connecting my laptop to each PLC individually. Power up the PLC and open Simatic Manager. The "New Project" Wizard window will open. Just click Cancel to close the window. Now click the Accessible Nodes icon on the toolbar. A window will open showing the identification of the PLC you are connected to. My window is showing MPI = 2 (directly). Make a note of this address and close the window.

Next we need to download a hardware configuration to the PLC. This is where we will rename the PLC node address. There are probably a couple of different ways to do this – following is how I accomplish this. All seven of my PLCs are the same model; Therefore, I am using the same hardware configuration. For the obvious reasons, I want to give each a different MPI node address. I have a project file that contains all seven of my PLC programs and one hardware configuration file. I open the one hardware configuration file, and then double click Hardware in the right hand window. This will open the HW Configuration window. In this window you should see your PLC with its MPI address given.

Remember when we clicked the Accessible Nodes icon and saw MPI = 2 (directly)? My Hardware Configuration Window is showing a MPI address of 7. Place your mouse cursor on the 7 and double click. Your CPU Properties window will open. It should open to the General tab. Look down and you will see Interface Type MPI with an address of 7. Click Properties and the MPI interface Properties window will open. Using the pull down menu, choose your MPI node address and make sure the MPI (1) 187.5kbps is highlighted and click OK. You are now back on the CPU Properties window where you will see your address has changed. Click OK and you will go back to the Hard Ware window where you can verify your MPI node address has changed.

You will now click the Save and Compile icon and then click the download icon. The Select Target Module window will open. Click OK and the Select Node Address window will open. Here you will see the MPI node address you assigned earlier. You will need to click the View button right below this. You will see the current node address appear, this should be the same as what you saw earlier when you clicked the Accessible Nodes icon. Simply click on this number and you will see it appear in the MPI address slot under the Enter connection to target station. Click OK and the Download to Module window will open. Click OK and the Stop Target Modules window will open. Click OK and the "Do you want to start the module?" Window will open. Click Yes.

Now go back to the SIMATIC Manager window and click the accessible nodes icon. You will see your new MPI node address. You can see this same article with pictures at http://www.morerobototics.com .

Posted in general | Comments Off on How to Change the MPI Node Address For a Siemens S7-300 PLC

Review of Takeoff Software for Estimating Construction

So often people want to rush out and buy estimating software or takeoff software without first trying to define their internal estimating processes. Once the estimating process is clearly defined, then and only then, can you actually try to compartmentalize the process into segments. So often the segment is really quantity takeoff. Takeoff of what you may wonder? That is like the million dollar question. This article will speak about the takeoff software process which usually associated with estimating software processes. The takeoff software process can often be takeoff of materials for some folks, and to many others, the takeoff process of scoped systems to create estimates or proposals. This review or comparison will not try to explain the estimating software process but bring to you valid quantity takeoff thinking among estimators in a quest to find which product thinks the way you do. These are the opinions of the author.

I will review and compare 3 types of measuring takeoff products:

It is extremely important to note that these are ONLY measuring takeoff programs, NOT estimating programs.

1) Planswift

2) On-Screen Takeoff by On Center Software

3) Electronic Plan Takeoff Software

All three products have their strengths, however, Planswift and On-Screen Takeoff are stand-alone products and Electronic Plan Takeoff is actually dynamically integrated live with Microsoft Excel which means that it starts and finishes and saves in Excel. They all integrate with Excel, however, you will have to evaluate your thought process and decide which of the three products work-flow think along the lines of how you think. For instance, what is the first thing you do when you get a set of plans? Typically, you start flipping through the plans to see how involved the project is and what type of work do you see that is attractive for your company. Then when you decide you are going to estimate this job, more often than not, you start like 80% of companies in the world of construction estimating by opening your takeoff master template Excel spreadsheet. You rename your spreadsheet to the new job or project and off you go performing takeoff. This is where the differences are:

In Planswift, you decide what drawing you are on and then you perform the measuring of an item you want to perform takeoff on the plan. Unfortunately, that is not exactly how an estimator thinks. Planswift does give you the ability to add a type of takeoff item on the fly by naming it and then perform takeoff of it; somewhat of a very manual and slow process. They also provide you with the ability of applying a type of assembly to a takeoff to aggregate quantities of items in that assembly. Not quite the way an estimator thinks. It forces you to jump to different screens which slows down the process. Typically, the main start of anyone’s takeoff process, or some may think of it as a checklist approach, is to start with your own spreadsheet of YOUR items. Those items can be material items or can be scoped assembly system items. Either way, by starting with a master spreadsheet say in Excel for example, many estimators think of this as a risk reducer, not to forget things they normally takeoff. Being that Planswift is a stand-alone takeoff program, it typically saves your takeoff images in Planswift instead of your estimate in Excel, if Excel is your estimating system. If you are using Excel, you have to manually save your takeoff measurement numbers in Excel and your takeoff images in Planswift or elsewhere, just not in Excel where the takeoff quantity resides. Again, if you want to integrate with Excel, they force you to either export or import takeoff items from Excel rather than being dynamically integrated live to Excel. They do however have the ability to dump the measured quantity from Planswift into any Excel spreadsheet or Word document. The main purpose or the primary focus of this program is measuring, therefore it does a good job at that function. Most of the other functions require you to jump around different screens, and essentially, you loose your thought of where you are. There are some features that attempt to address the estimating process, however, there are many features that are missing for Planswift to be a full fledged estimating system; it is NOT one. Planswift does integrate with the leading estimating system Sage Timberline, but the integration is weak. Since Timberline’s power is in assembly takeoff and where most estimators reside in Timberline, Planswift does not give the estimator the ability to add quantities of miscellaneous Timberline items or one-time items that need to added on the fly to an assembly while they are in Planswift at the Timberline interview screen, and while being in the measuring phase. Planswift does allow the deleting of assembly generated items as well adjusting assembly item quantities in a different screen. Again, to perform all that, you are forced to jump around to different screens. No assembly is ever perfect in any estimating system since project conditions are always uniquely different, therefore, having to add items to an assembly is extremely important. That adding of items and associated quantities is an absolute requirement any estimator typically has to do during the takeoff measuring and estimating phase; something that Planswift struggles with as related to Timberline Estimating. Planswift does allow the direct send of measurements to Timberline Estimating items and assemblies while in Timberline Estimating, just as you would do with the old digitizer measuring boards. Training, support and maintenance are extra for Planswift. On-Screen Takeoff by On Center Software, and Planswift charge their annual maintenance and support fees per license (mandatory) which costs the end user more expense annually especially if a customer has more than one license.

On Center’s On-Screen Takeoff is the Grand Daddy of software takeoff products due to the fact that it has been around the longest. On Center recognizes that On-Screen Takeoff is primarily a measuring program. That is why they have a separate estimating program named QuickBid for those who want an estimating program. On Center does not try to trick you into thinking it is an estimating system. In On-Screen Takeoff, you also decide what drawing you are on and then you perform the measuring of the plan. BUT, before you start, you can load a master set styles of things you typically takeoff or measure from your own library. That process seems to be less complicated than that of Planswift. On-Screen Takeoff does give you the ability to add a type of takeoff item on the fly by naming it and then performing takeoff of it; somewhat of a manual and slow process as well. The program does come with many features that are primarily focused on simple measuring to advanced measuring issues all with attention to detail regarding easy navigation for the takeoff process. On Center does a very good job at that. However, there seems to be a disconnect of thought from an Excel spreadsheet items you may use for estimating and/or proposals. The integration to Microsoft Excel is not a dynamic live link, more like an after thought in my opinion. Yes, you can establish links to named styles to cells or ranges in Excel, somewhat rigid. But the question you will have to ask yourself, which will happen more often than not is: What do you do when you need to add things on the fly during takeoff and in an Excel spreadsheet? Again there will be manual associations you will have to establish with Excel which is another major slowdown. You have to manually save your takeoff measurement numbers in Excel and your takeoff images in On-Screen or anywhere you decide, except the takeoff images will not be saved in Excel where the takeoff quantity resides. This type of situation arises when a takeoff program is a stand-alone program. On Center’s On-Screen Takeoff has the best integration with the most widely used estimating system in the USA: Sage Timberline Estimating. It basically mimics the same interview process as you would do with the old digitizer measuring boards. By working directly with Timberline, On-Screen Takeoff allows the estimator to perform takeoff of a Timberline variable question and immediately returns back directly with the takeoff quantity in a Timberline assembly at the variable question. By virtue of this process, On-Screen Takeoff allows the estimator to continue his/her Timberline interview process in Sage Timberline Estimating by reviewing/massaging generated quantities, or adding items in a Timberline assembly as the estimator see fit. That workflow process gives full control to the estimator, good job On Center. Training, support and maintenance are extra for On-Screen Takeoff. On-Screen Takeoff by On Center Software, and Planswift charge their annual maintenance and support fees per license (mandatory) which costs the end user more expense annually especially if a customer has more than one license.

This next system is ONLY if your estimating system or proposal generator is Microsoft Excel. Electronic Plan Takeoff Software is a plug-in for Excel. You start your spreadsheet, you perform the measuring takeoff, you may even add some more items on the fly all the while you are in the measuring phase in the Electronic Plan Takeoff program. When you are done, even if you added items on the fly, they automatically appear in your Excel spreadsheet. Excel is the control of everything. Your project is started in Excel, your takeoff is saved in Excel, the estimate or proposal is/can be produced there in Excel; one program, one place. Many takeoff programs interface with Excel somehow, but only Electronic Plan Takeoff is live linked with Excel, meaning all your Excel spreadsheet descriptions appear in the measuring takeoff program so you always know where you are in Excel. That is a huge difference in comparison to Planswift and On-Screen Takeoff. You can even change a description of a takeoff item in Electronic Plan Takeoff and it is automatically changed live, in your Excel spreadsheet. When you talk about the estimating and takeoff phase you must keep processes cleans and easy and this program does just that. There is no getting lost in this program. Just like the other reviewed programs above, the central focus of this program is takeoff measuring, and it does a GREAT job at that. The navigation within the program is really simple and easy. It is not made to work with other estimating systems, but there is a version that allows the direct send of measurements to any Microsoft Windows program awaiting a keyboard entry, just as you would do with digitizer measuring boards. There is also a version that works with digitizer boards as well. If you use Microsoft Excel for estimating, or takeoffs, or proposals, then this Electronic Plan Takeoff program for Excel would be your best choice. The integration to Excel is unmatched in Electronic Plan Takeoff compared to Planswift or On-Screen Takeoff. What is quite different in Electronic Plan Takeoff is that training, support, and maintenance are INCLUDED with a purchase, whereas training, support and maintenance are extra for Planswift and On-Screen Takeoff. Moreover, annual support and maintenance for Electronic Plan Takeoff year two and beyond is a low fee per company per year, instead of per license. On-Screen Takeoff by On Center Software, and Planswift charge their annual maintenance and support fees per license (mandatory) which costs the end user more expense annually especially if a customer has more than one license.

Microsoft and Excel are registered trademarks of Microsoft Corporation. Planswift is the registered trademark of Tech Unlimited, Inc. On-Screen Takeoff and QuickBid are registered trademarks of On Center Software, Inc. Sage Timberline Office, Sage Timberline Estimating are registered trademarks of Sage Software, Inc.

Posted in general | Comments Off on Review of Takeoff Software for Estimating Construction

Learn How to Fix “Runtime Error 53 File Not Found” Easily

Computer errors generally plague us a lot. They have to be removed immediately before they can cause any further problems. One such error is the run time error 53. It shows the message “runtime error 53 file not found”.

In this error, problem occurs when a software program that is installed on the PC shows this error because it is trying to reach a DLL file that has been removed from the windows registry. This registry contains all the files that are used by Windows for executing any kind of commands by human users. This DLL file might have never been installed on the computer itself.

To fix runtime error 53 from your system, some simple steps have to be followed. Such steps include clicking on the start menu and then landing at the control panel. After you reached the control panel, open the programs and features icon. Open up all the programs stored in the computer through it. Uninstall the program, which produced the run time error 53 message. A window will also open up telling the user that the program has been removed from the system.

To make sure that the DLL file is stored again on the computer, one has to remove the program and then put it back. The program can be reintroduced into the system through a hard disk or a CD. Instructions will appear on the screen as this program gets installed. After clicking on the install it now option, the user will see the option of terms and conditions on the screen. Click on the “I agree” choice to continue with the installation. The operating systems that generally display this error are Windows XP, Windows Vista and Windows 7.

Run the program to ensure that runtime error 53 is not displayed again. If the error is still being produced, then contact the company, which supplied you with the software.

It is also intelligent on your part if you find out about the compatibility of your software with the operating system of your computer or other software. You can find out about this compatibility through an online research. The website of the software developer can also yield you such details. Tell the software developer about the intricacies of your system to get an adequate response from him about the runtime error 53.

However, the last and most easy solution to fix “runtime error 53 file not found” error is using windows registry cleaner software. Registry cleaner software can always eradicate any registry errors produced by wrong entries, which cause a runtime error 53. It can delete all the useless entries in the registry that are causing such an error. Using such software can ensure that you get an error-free system.

Posted in general | Comments Off on Learn How to Fix “Runtime Error 53 File Not Found” Easily

Recommended Software for Arena Management

When there is a little over a month left to enter the data for a thousand plus cattle penning teams into a fickle spread sheet software program that was built by good intentioned volunteers; the last thing anyone should be doing is looking for replacement software. However, as any event/entry secretary or producer knows this is sometimes the lifeline that is needed to get the job done.

The preparation of all of the necessary data combined with balancing a three-quarter of a million dollar show in the six weeks prior to its start should have been enough to do. Throwing in a new piece of software to learn and master would be considered ludicrous to say the least. The producers deemed it to be a necessity in view of the history of inconsistencies in the program currently in use.

With a three-year old recommendation in hand and very little back ground checking, Arena Management Software became the chosen lifeline. The software was purchased, loaded onto the computers, played with for a day or so and then our team went to work. The KCI support group was there, day and night, to help with the learning curve and any snags that presented themselves. Our team quickly realized that the new user-friendly software program we had taken a chance on was going to be our ongoing choice for future events. The show was a success. The producers and contestants were happy. All was good in our world!

There have been a lot of years pass by since those short six weeks when our group became acquainted with the Arena Management Software. The program still provides a user-friendly format that has the talent to produce minimal data to realms of reports. From rodeo to cattle penning events the product continues to amaze our team with its ability to perform in and out of the arena.

Posted in general | Comments Off on Recommended Software for Arena Management

Benefits of an Android TV Box

The Android TV box is a useful piece of kit that connects to the TV via the HDMI port to offer most of the features of Android. This type of set up is very flexible and easily connects to most TVs with the right port and is a lot cheaper than a smart TV. Here are a few of the benefits of using the Android TV box:

Endless apps

One of the most appreciated benefits is the ability to use and install the endless apps that are now available on the Android operating system. By visiting the Google Play store using the internet connection, it is possible to install the latest apps related to not only multimedia content, but also audio editing applications, games, books, magazines, sending email, or signing into social media accounts, such as Facebook and Twitter.

TV support

By connecting the Android TV box to the TV at home via the internet; It is also possible to connect to other devices in the home, such as those that make use of technologies like Airplay, Miracast, DLNA, or others that function with Android. This makes it very flexible to share various types of multimedia with the TV. For instance, it is possible for an Android compatible tablet or smartphone to interact and control the TV while also giving the option to share files with a laptop or even watch a downloaded series or a movie on the large screen. Overall, this type of setup gives a simple gateway to get the internet on the TV.

Great price

The cost of upgrading a standard TV to benefit from all the possibilities of Android is relatively cheap compared to buying a smart TV. Plus, the combined standard TV and Android TV box can offer a lot more than a standard smart TV.

Regular updates

The Android operating system is updated on a regular basis, which means the latest version of a game, application, or system is always available. Plus, this is usually done automatically so there is no need to keep searching for updates when logged into the app store. This is significantly more convenient than a smart TV which can take a while to receive updates, especially when every brand of TV needs to have its own update created and released.

All in all, the Android TV Box makes it possible to enjoy the connectivity and versatility of Android on a standard TV set up.

Posted in general | Comments Off on Benefits of an Android TV Box

How Has Technology Changed Art?

We all are witnessing the changes being made in the art these days. Technology has the power to change anything. It is changing the traditional art into digital art.

Amazing digital art has taken place of traditional art. Digital art is exploring itself in many different ways that one can imagine. Different software is developed to increase the presence of digital art.

Photoshop Artists are one of the most common digital artists who give an amazing look to a picture with the help of imaging software and different applications.

These applications are developed with the help of technology. Anyone can be a digital artist having knowledge and proficiency in Photoshop.

Difference between traditional artists and digital artists is that traditional artists use paint and cement for their art and digital artists use imaging software and applications in their art. Some of the applications have the power to create 3D art work.

Technology has taken art into a new level of creativity. Let us talk about how technology has changed traditional art into digital art. We know that internet is ruling the world with its power. So, artists decided to present their art online with the help of internet. This is possible with use of technology.

You must have seen art galleries and attended painting exhibitions in your life. These doesn’t work well these days so artists find a way where they can get more attention and more praise for their work. Most of the artistic stuff is now seen online and is circulated to the art lovers.

There are some places where exhibitions are held and we do respect them. But presenting paintings, sculptures and art work online is in trend. Some of the artists are also showing their art on the basis of card swipe panel or coins.

How this work – when you enter coins or swipe card in the panel, the panel shows you some of the art work for a few minutes and then gets closed and if you want to see it again or explore more, further you need to swipe your card or add coins into it. This is how artists are using technology.

How digital artists are using technology for their art work

Digital artists already in touch with technology are aware of the systems that are in trend and use them to create their art work and sell them online.

Some of the professional digital artists are earning a lot of bucks by selling their art work. They can also design the ones that you want and are also ready to make any modifications you need.

They use different software to explore their skills and made it more impressive. They are using technologies that offer new ways to express their art work in a realistic way for much more time.

They are using different types of media and mix them to provide a more creative art work. Their 3D art work looks as real as it is present live in front of you.

Technology not only brings changes in education, medical field, industry and business but also brings a huge change in the art work and the artists as well.

Technology opens different paths for the artists to enter into for a good earning. They made their profession more powerful along with their art work.

In our busy lives we hardly get time to meet each other and our loved ones. How can it be possible to see exhibitions and galleries? So technology has brought this change in the art workers to show their skills and talent to people from anywhere in the world.

Technology is getting advanced and making more useful for the common man as well as artists. Technology has provided us with several things that we should be thankful. One of them is digital art work.

Posted in general | Comments Off on How Has Technology Changed Art?

Advantages to Android Game Development

The industry of mobile game development has introduced a very important aspect to the market – the ability to conceptualize, develop, and release video games on devices with far more success and ease than ever before. And with the Android app marketplace only requiring a one-time fee for submitting an application, the cost becomes almost negligible to put the product out for millions of customers to find. Even the submission process is drastically shorter than on most other smartphones, as the app regulation is far more lenient for the Android OS.

Another drawing point for developing games on Android devices is the programming language featured- Java. Java has long been one of the most popular programming languages ​​for video game developers, and that makes it extremely easy for the average programmer to pick up Android development for the first time. Compared to most other mobile platforms, which usually sport modified or newly invented languages, the learning curve is decreed to nearly nothing, so a new developer can complete a game in a fraction of the time.

Another unique aspect to Android game development is the lack of standardization in the droid phone family. As the Android OS is not licensed to a single mobile phone making company, the phones themselves can vary to an extreme degree in terms of features and hardware specifications. While one device may have a fully functional A-GPS and HDMI video compatibility, another may have a QWERTY keyboard and no GPS at all. While this is certainly appealing to some developers, as they are likely to find a phone that will meet their hardware needs reasonably, it will also restrict the potential audience, as some phones will not be able to support the more complex applications.

When the game development process has finally reached the point where it can be released to the public, the developer is presented with yet another choice- which market would the game be most visible in? Unlike the iOS, there are numerous marketplaces and app stores for Android phones, each one with it's own advantages and disadvantages. From the basic Android marketplace, built to only display the apps compatible with the phone currently being used, to the Amazon app store, which offers a different free app every day, the myriad of marketing strategies can be almost daunting, which makes it all the More useful that an application can almost always be entered into multiple marketplaces without issue. However, whenever it makes sense to spread attention across several different fields is another question entirely.

The Android game development process overall really gives the most variety on the smartphone market. From start to finish, strategies can be hand-tailored to the developer's desires, making the game as close to the original concept as currently possible. While the audience may not be as large as that of iPhone users, the Android presents itself as a strong contender, purely through its accessibility. And with the largest variety of smartphones on the current market, the possibilities for development are inexhaustible, and continued releases can only add to the capabilities the platform has to offer.

Posted in general | Comments Off on Advantages to Android Game Development

Top 25 Terms All Computer Students Should Know

The following basic terminologies are considered the top 25 terms all computer students should know before they even begin their studies:

1. Bit: Binary data storage unit valued at either 1 or 0.

2. Byte: Eight data bits valued between zero and 255.

3. Word: Two data bytes or 16 data bits between zero zero and 16,535.

4. CD-ROM: A storage disk with approximately 640 megabytes of capacity.

5. CD-ROM Drive: Hardware used for reading and writing to CD-ROMs.

6. Storage Media: Magnetic devices that permanently store computer data.

7. File: Permanent storage structure for data kept on a hard drive or other permanent place.

8. Virus: Unauthorized programs that infect files or send themselves via email.

9. Vulnerability: When unauthorized access can be gained due to software errors.

10. Security Flaw: When attackers gain unauthorized system access due to a software bug.

11. Worm: Unwanted programs accessing computers via application / system vulnerabilities.

12. Hardware: Physical parts of computer (case, disk drive, monitor, microprocessor, etc.).

13. Software: Programs that run on a computer system.

14. Firmware: Software that has been permanently written into a computer.

15. ISP: Internet Service Provider.

16. BIOS: The basic input / output system computers use to interface with devices.

17. MIME: Multipurpose Internet Mail Extension.

18. Boot: What happens when a computer is turned on and beginning to run.

19. Crash: When computer software errors occur and programs fail to respond.

20. Driver: Program that understands interfaced devices like printers and video cards.

21. Network: Cables and other electrical components carrying data between computers.

22. Operating System: A computer's core software component.

23. Parallel: Sending data over more than one line simultaniously.

24. Serial: Sending data over a single line one bit at a time.

25. Protocols: Communication methods and other standard Internet / networking functions.

These are the top 25 terms all computer students should know before they even begin their technical training. Most computer students know much more. In fact, everyone who uses a computer these days should understand these terms so they can be better informed about the important tool that is so integral to our daily lives.

Posted in general | Comments Off on Top 25 Terms All Computer Students Should Know

Determining the Best Type of Fastener to Use For Outdoor Furniture Construction

If you want to learn about selecting hardware for your next outdoor furniture project, then you'll want to read this article. Specifically, I'll be telling you about what type of hardware will perform best, why the type of metal used for fasteners and the finish used are important considerations, and how properly protecting or limiting exposure of your furniture to wet and winter conditions can increase Life span. After you're done with this article you will understand that the best choice of hardware for your outdoor furniture project is dependent on furniture style, material used for construction, selected location for the furniture and budget.

Selecting proper hardware for your furniture will help ensure a long life span, as well as improve the overall appearance of your furniture. Part of the problem is knowing what hardware to select when there are so many options available at the hardware store. The typical Lowes or Home Depot carries a huge selection of stainless steel, hot dipped galvanized, bright galvanized, plain steel, coated steel and brass bolts, nuts, washers and screws. Each type of fastener is suitable for certain applications, but not all are ideal for outdoor furniture applications.

In fact, choosing the wrong fasteners can greatly shorten the lifespan of your furniture, contribute to rot of wood furniture, cause unsightly staining, and even make your furniture unsafe to use.

One thing that needs to be noted right up front is, do not ever use unprotected steel fasteners for outdoor furniture, they will rust very quickly, and the steel will react with the tannic acid in the wood causing streaks and staining. The tannic acid actually speeds up the corrosion of the fasteners. Have you ever seen a wooden fence with black streaks running down the boards from the nails? This fence was installed with the wrong type of fasteners. The same thing will happen to your furniture. Even worse, as the fasteners rust, they will speed up the decay process of the wood around the rusted fasteners, ruining your furniture and making it potentially unsafe to use.

Hot Dipped Galvanized

Screws and bolts treated by hot dipped galvanizing are specifically designed for use outdoors. Electroplated galvanized or bright galvanized fasteners will very well not hold up as well as the hot dipped galvanized hardware. Zinc is used as a coating in both methods, and acts as a barrier against the elements and the tannic acids in the wood.

I strongly recommend only using screws or bolts in the construction of outdoor furniture, however. The galvanized finish on nails, either electroplated or hot dipped, can easily become damaged while hammering them in, exposing the nail head to the elements and allowing them to begin rusting quickly.

Adequate care must be taken when installing galvanized screws. Drill pilot holes in hardwoods, and be sure to use a bit that is not worn and intolerable to skipping in the screw head. For whatever reason, the galvanized screws seem to not be as well tempered as other steel fasteners, and are more likely to either snap off or have the heads strip out while installing them. Due to the permission required for the hot dipped coating, galvanized bolts do not have as tight of tolerance on the threads, and are more likely to strip if over tightened.

Hot dipped galvanized fasteners are a fine choice for many outdoor furniture applications, including Adirondack Chairs, but are not the best choice for use in woods, such as teak.

Stainless steel

Stainless steel is the best choice for use in woods with higher levels of tannic acid, such as teak. Stainless steel is an alloy or blend of steel, nickel and chrome. The ratio of the other metals with the steel determine the weather and corrosion resistance of stainless steel. Because the steel is mixed with other softer metals, the stainless steel is not as strong, so predrilling of screw holes is highly recommended in all applications, and essential in hardwoods such as teak and mahogany. The added corrosion resistance more than outweighs any shortcomings that the metal may have, especially in outdoor furniture applications.

While stainless steel fasteners are the most rust resistant, they are also the most expensive of the options we are discussing. However, using stainless steel fasteners will add years of life to your furniture. In the respect, they are an investment that will pay out for years to come.

Brass

I have seen brass used in some commercially produced outdoor furniture, but do not recommend it. While brass does not form red rust, and is well suited for many wet applications such as toilets and sinks, it does tarnish and corrode. It is also very susceptible to the tannic acids in wood, which will cause it to fail more quickly. Brass screws in particular Do not have sufficient strength for outdoor furniture applications.

Outdoor or deck screws

In the past several years a number of manufacturers have introduced outdoor fastening products specifically marketed for deck building. These will typically be green, gray, tan or brown. These screws are either ceramic or plastic coated to delay the metal reacting with the wood acids. The specific coating methods are proprietary to each manufacturer, and can be a combination of electroplated galvanizing and plastic, or a baked on ceramic.

I have used these fasteners in furniture applications and they perform just fine. Unfortunately, I have not come across bolts with this type of finish. The brand of screw I used was Deck Mate, and they were available in tan and brown, so that the color can be selected to better match the wood being used. These screws are ceramic covered, and the manufacturer provided a coated bit for installation, which was designed to not damage the ceramic coating at the screw head. If you choose this type of fastener, be sure to compare the cost with stainless steel, as the price will vary. If the stainless steel is reasonably comparable in cost, it would be the recommended fastener.

Always be sure to read the manufacturers specifications on the box to be sure that the screws are suitable for your application.

Other Considerations

If you are building furniture that will be located on a covered porch or patio where it will be protected from the elements, the concern will be the interaction between the wood and the fasteners, much more so than the weather. Furniture that will be exposed to the elements all year, such as a garden bench, or an adirondack chair in the corner of your garden, will have to be constructed with much more care and concern to ensure that they hold up more than just one or Two winters.

Additional considerations must be made beyond just the choice of what type of fastener to use, though this is very important. For example, fasteners should not be located where water where collect and sit on the fasteners for an extended period of time. The screws that attach the seat slats to an Adirondack chair are a prime example- typically these screws will be countersunk below the surface of the wood. This will allow water to collect in the screw holes, shortening the life span of all but stainless steel fasteners, and prolonging the exposure of the wood to water, which will increase the rate of decay. In applications where the furniture will be exposed to the elements year round the screw heads should be driven flush with the surface of the surrounding wood.

Construction and design of the furniture are also important considerations. Are the horizontal surfaces of the furniture constructed in such a way that will allow them to shed water, rather than collect it? Think of a picnic table with a slatted or board top. The gaps between the boards allow water a way to run off the top and not pool up.

Conclusion

Stainless steel is usually the best choice for outdoor furniture applications, although the cost may be prohibitive for some. There are other less expensive fastener options available that will perform acceptably. Do not use unprotected steel fasteners for outdoor furniture applications under any circumstances. Know where and how you intend to use your furniture and design it for the conditions it will be subjected to.

Posted in general | Comments Off on Determining the Best Type of Fastener to Use For Outdoor Furniture Construction